Monthly Archives: January 2023

Renovate Home Loan

If you want to renovate your home, then you’ll need to find a suitable loan to get the job done. However, there are certain guidelines and requirements you need to follow before you can get a mortgage to carry out the project.

What Is a Renovate Home Loan?

A renovate home loan is a way for homeowners to tap into their home equity and get the funding they need for remodeling. It also allows them to keep their house energy efficient, add windows and siding, and repair damaged walls. However, the process of applying for one can be complicated.

Unlike conventional mortgages, a renovation loan is based on the value of the home after renovations have been completed. This is important because lenders set their rates based on the ratio of the loan to the appraised value of the home. The more the house’s value has increased, the more the lender is willing to lend.

Before you apply for a home renovation loan, make sure you have a realistic idea of the amount you will need to borrow. Some of these loans are limited to a certain amount and have a short repayment period.

Renovation mortgages are available through government-backed agencies, including the Federal Housing Administration (FHA) and the Department of Veterans Affairs (VA). While the FHA and VA loans have stricter requirements, they are designed for lower-income borrowers.

Can You Get a Home Loan to Renovate?

Whether you’re planning a new kitchen or simply need some roof repairs, it’s important to understand how to get a home loan to renovate your property. Renovation loans can save you money in the long run and make your home more energy efficient.

The best type of renovation loan depends on your budget and property. Before applying for a home renovation loan, check your credit score to see what type of borrowing option is best for you.

One of the most popular options is a home equity line of credit, also known as HELOC. This loan is more affordable than a personal loan but has variable rates.

Another option is the Freddie Mac CHOICERenovation loan. This loan allows borrowers to finance the purchase and renovation of their home, making it more convenient than a traditional mortgage.

You can also opt for a Fannie Mae Homestyle loan. This loan has a similar structure to the 203(k) but requires a little more down payment.

As with all loans, the costs of a home renovation loan will depend on the loan type you choose. A loan for home improvement can help you pay for a new shower, kitchen remodel, or even finishing your basement.

How To Get a Loan to Renovate Your Home

If you are looking to improve the look and function of your home, it’s worth considering a home renovation loan. These loans allow you to finance a variety of repairs, from new siding to a new roof. You can also use these funds to make your home energy-efficient.

Renovation loan programs vary from lender to lender. Some require a minimum credit score. They can also charge a premium.

Fannie Mae and Freddie Mac offer home improvement loans. The HomeStyle program offers up to 97% of the home’s future value. However, they do limit the amount of money you can borrow.

Another loan option is a construction loan. This type of loan replaces your current mortgage and is often used for major repairs. It can be a complicated process and carries a high interest rate.

A personal loan, or a credit card, can also be a good way to finance your home improvements. Credit cards tend to have higher interest rates than home improvement loans, though.

For the best deal, it’s important to find a mortgage broker. Not only will they help you find a lender, but they can guide you through the process.

Renovate Home Loan Financing

Renovation home loan financing is a great way to help you improve your home. However, you should be aware that there are more risks involved in renovation mortgages than you may realize. The good news is that if you choose a renovation loan, you will be able to make your house more comfortable and energy efficient.

Homeowners can take advantage of this type of loan if they have a significant amount of equity in their property. Unlike conventional loans, however, renovation mortgages involve a lot of paperwork and oversight.

In order to qualify for a home renovation loan, you will need to have a minimum credit score. Most lenders will require a FICO score of 680-700. This allows you to get the best interest rates.

Alternatively, you can try a credit card with a no-interest promotion. While it will cost you less, it is important that you are able to pay back the balance quickly.

Another option is to apply for a home equity line of credit (HELOC). With a HELOC, you will be able to withdraw money over a specified period of time, but you will also have to pay interest.

Renovate Home Loan Guidelines

If you are looking to renovate your home, you need to find out what is available to you. A home renovation loan will help you get the job done at the right price. However, before you apply, make sure you understand the pros and cons of each option.

You can apply for a home renovation loan in a number of ways. Some offer low interest rates and flexible repayment options. For example, you can borrow money from your home’s equity or use a credit card that offers no interest for a period of time.

Another option is a cash-out refinance. This loan is especially beneficial for homeowners who have a lot of equity in their homes. When you refinance your mortgage, you can tap into the equity in your current home and use it to renovate.

Renovation loans are also available from private banks. They are much more flexible than traditional loans. Many private banks allow for a higher percentage of the home’s value in your renovation loan. The biggest risk with these loans is over-improving your home.

Renovate Home Loan Requirements

If you are planning on renovating your home, you may be interested in getting a loan to cover the costs. However, before you apply, it is important to understand what kind of loan you will need. This can help you get the best deal for your renovation project.

There are several different types of renovation loans, each with its own set of requirements and benefits. Before you decide which type is right for you, it is a good idea to talk to a mortgage banker. A specialist can give you advice and make the best use of your loan.

Whether you choose a jumbo or standard 203(k) loan, you will need to be able to meet certain requirements. Your credit score, home appraised value, and the value of your home after renovations are all important factors.

Typically, you will need to have a credit score of at least 500 and a down payment of at least 3.5%. In order to qualify for the FHA 203(k) loan, you will also need to submit a construction plan. The construction plan will outline the details of your renovations. It will also list the cost breakdown.

Renovate Home Loan Debt Ratio

A renovation home loan is a great way to improve your pad with the minimum of fuss and bother. If you’re interested in tackling a remodel, there are plenty of lenders willing to work with you. Some of these loans even allow you to cash out. While they may not be for everyone, these mortgages can get you started down the path to homeownership. Regardless of what you decide to do, make sure you read up on the finer points of the industry.

Renovate Home Loan Approval Process

When considering a renovation home loan, it is important to understand the requirements. You should also consider the costs and time required to complete the project. It is also important to choose the right type of loan. There are several types of mortgages available, each with its own qualifications.

Renovation loans usually have stricter requirements than traditional mortgages. They require an appraisal and construction plans. Lenders also check your debt-to-income ratio and credit score.

Renovation loans are a great way to finance home improvements. Unlike conventional loans, they spread the cost over a period of years, and allow you to borrow against your home equity. However, they are not designed for recent buyers, and the interest rates tend to be higher.

Home equity line of credit (HELOC) loans fall between renovation mortgages and traditional loans. The lender will determine the amount you can borrow based on the value of your home after you complete renovations. HELOCs can be used to fund both large and small projects.

FHA 203(k) renovation mortgages are insured by the federal government. FHA loans come with a lower down payment and require only a 580 credit score.

Water Damage on Walls

Advice For Water Damaged Walls

When your wall experiences water damage, it is vital to take action to renovate the damage. Having a professional help you dry out your wall can ensure that you aren’t left with a permanent water damage problem. If you are unsure of what to do, here are some guidelines that can be of great assistance.

What Caused Water Damage To The Wall?

First, you’ll need to determine what caused the water damage? Was it a leak? Was it a burst pipe? Was it an appliance leak? You’ll need to trace the source of the leak and repair it so that further water damage does no occur.

When looking for signs of water damage in a wall, you might be surprised by the amount of hidden or unseen problems you may face. Water can get into framing materials, insulation and even the paint on the walls. This could result in damage that can cost you a lot of money to fix.

A small hole or a small leak is the most obvious sign of water damage, but it isn’t the only way. You might be asking yourself, “How do I know if my wall has a problem?” It’s best to have a water damage expert come out to evaluate your situation and give you a clear picture of what needs to be done.

The first step in any water related repair is to find out what caused the problem in the first place. This will allow you to avoid costly and dangerous mistakes. Using the right tools is also a must. Remember, the best way to prevent further damage is to act fast.

Does Homeowner Insurance Cover Water Damage?

If you have a flood or a burst pipe, your homeowner insurance might not cover the damages. The truth is, water damage can be devastating and can wreak havoc on your belongings. However, it is possible to file a claim.

In fact, it is quite common for homeowners to make a small water damage claim. Approximately one in every 50 homes makes a water damage claim, averaging about $7,000.

While water damage may not seem like a big deal, it can be very costly to repair. Some homeowners will opt to hire a contractor to handle the job. They will want to keep copies of receipts for any repairs that they do. Having receipts handy can help your insurer’s adjuster to quickly evaluate the extent of the damage.

Depending on your insurance policy, the most expensive repair might be a small water leak in your refrigerator. However, if your home is flooded, your insurance might pay to replace your furniture and appliances.

Homeowners insurance can also cover water damage due to vandalism. It can also cover the costs of damage caused by extreme weather. For example, if your pipes freeze in the winter, they might break and cause a lot of water damage.

Risk Of Mold From Wall Water Damage

If your walls have suffered water damage, there is a risk that mold will grow. If this occurs, it will become a health concern for you and your family.

Mold is an unpleasant fungus that grows in damp, humid conditions. It is most common in homes with moisture and lack of light. In addition, mold can be toxic, and can cause allergic reactions.

Fortunately, you can take measures to prevent mold from growing. One of these steps is to open windows and let air circulate. Another is to use a dehumidifier. These devices will help reduce the level of humidity in your home, which will discourage mold growth.

If your wall has suffered water damage, it is not a bad idea to clean the affected surfaces. Do not use ammonia-based cleaners and other detergents that contain chlorine bleach. They are unsafe when mixed together.

After the affected surfaces have dried, you can begin to remove any mold. This is not a quick process, and you may have to contact a professional to do the job for you.

How To Dry Out A Wall After Water Damage

If you have experienced water damage to a wall, you may wonder how to dry it out. There are several methods to get the job done. The key is finding the right method for your situation.

The first step in drying out a wall is to find the source of the problem. In most cases, you should contact a professional to fix the issue. They can use tools and instruments to locate the leak and perform the necessary repairs.

You should also remove anything from the wall that is wet. This includes shelving, paintings, wall coverings, insulation and other porous goods. This can speed up the drying process and keep your items from becoming damaged further.

The best way to get a wet wall dry is to allow natural ventilation. This will remove moisture from the air and reduce lingering odors.

Using a high-capacity air mover is a great way to suck moisture out of the air. High-volume fans can also help speed up the drying process.

You should also remove any wet insulation from the wall. Leaving this in place can promote mold growth.

Wall Water Damage Treatment

Water damage on the walls of your house can lead to serious structural problems. If you find this to be the case, it’s important to get the repairs done as quickly as possible. You should also be aware that untreated water damage can lead to the growth of mold in a very short period of time. Mold can pose a health risk, and can be costly to repair.

Depending on the severity of the water damage, you may need to hire a professional to complete the repairs. They will be able to protect your home from further damage and ensure the work is completed correctly.

Aside from drywall, water damage on walls can also affect other surfaces. Stains can develop, and peeling paint can occur. Both can be removed with a detergent solution or a sealer.

Wall Water Damage Removal

Water damage is a common problem that can occur in many different places, and for many different reasons. It’s important to know how to identify and deal with it in order to prevent additional damage.

Identifying the source of water damage is the first step. Contact a professional to help you assess the damage and provide an estimate for repairs.

You should also remove any loose items from the area. This is especially important in the case of drywall. Doing so will speed up the drying process.

Using a dehumidifier is an excellent way to dry out a wet room. A low-grain refrigerant dehumidifier will reduce humidity levels and inhibit mold growth.

If you don’t have a dehumidifier, you can remove the moisture from your air with a mop or wet vacuum. If your walls are still wet, it’s a good idea to open windows to let the air in.

Wall Water Damage Repair

Water damage to a wall can be devastating. Not only can it cause unseen mold and mildew growth, it can also compromise your home’s structure.

If you notice visible signs of water damage to a wall, contact a professional for repair. You don’t want to spend more time trying to fix the problem on your own, especially if it’s structurally harmful to your home.

Wall water damage can be caused by several sources, including inside sources and outside sources. The first step in fixing water damage is to find out what the source is.

In addition, you’ll want to know what signs to look for. Some common signs include cracks, discoloration, and peeling paint.

Another sign is when the drywall buckles. This may be the result of water behind the drywall. That’s why you should take a closer look at the walls.

When you have water behind the drywall, it’s possible to stretch the paint and make the surface appear spongy. Regardless of the paint type, this can occur if the drywall is left wet for a long period of time.

Wall Water Damage Solutions

Water damage is a problem that can have a serious impact on the structure of your home. If not caught in time, it can lead to mildew, mold, and structural problems that could cause major headaches for homeowners.

Fortunately, there are ways to get your home back to its former glory. For starters, you can try to dry out the area as much as possible. A fan or a dehumidifier can speed up the process.

Another thing to do is to seal the leak. The best way to do this is to call in a professional plumber. An experienced one can pinpoint the source of the leak and give you an estimate of the cost to repair it.

Identifying the source of the water is an important step in the process of getting your walls back to their former glory. Having a licensed plumber check out your pipes can also help prevent further problems from occurring.

One of the most noticeable signs of water damage is a stained wall. This can be due to a wide range of causes, from a cracked pipe to a leaking tank.

How to Install Vinyl Plank Flooring as a Beginner | Home Renovation

Welcome back to Fix This Build That. Today we’re installing vinyl plank flooring. I’Ve installed ceramic tile before, but this is my first time doing: laminate or vinyl flooring now I’ll be installing this in this laundry room and giving you all the beginner tips that I learned along the way I started by moving the laundry machines and everything else out Of the room and apparently elves, don’t really steal your socks, They just hide them under the dryer, But while the machines were gone, It was a great time to paint the rest of the wall that I didn’t paint because I didn’t think anybody would ever see it.

Now I know I’m not the only one so comment down below and tell me where your unpainted walls are hiding in your house. Next, I pulled off the quarter round molding to prep for install.. I would have pulled off the baseboards too, but since I have wainscoting installed, It would make a huge undertaking and in the end you won’t really be able to tell the difference anyway In the vinyl planks that I’m using are a little under 4 feet.

Long and just under 8 and 3/4 of an inch wide I’ll have a link below to this exact product, as well as all the tools that I use during the vinyl plank flooring, installation Which I tried to keep as basic as possible.

Now, before the install you need to do a little planning and for a nice-looking room, you don’t want a super-short board at the beginning or end of a row and you don’t want to narrow run at the end of your installation, either on the install instructions.

With your flooring should help you figure this out or You can nerd out like, I did and make a 3d model of the room and lay out the planks Exactly how you want them beforehand. Seriously, though, for an over analyser like me, this is the only way To go, you can map out and stagger the seams and play around with the different layouts, based on the bump outs in the room to see how it’s all going to look, if you don’t have any programs, you can do this with just find a nerdy friend And have them do it for you or you can Always just use graph paper too, And with my layout all done.

I went back to the laundry room to start the install. You always want to start on the left side of the room in a corner due to the positioning of the tongues and the grooves on this flooring. I pried up the transition piece between the current vinyl sheet floor in the carpet.

Then I cut back the carpet to make room for the new transition strip, which is a metal channel. Then there was a small gap between the plywood underlayment of the vinyl sheet and the tack strip the carpet.

So I filled in the gap to give that channel a little place to be attached. I used a sample piece of the flooring as a spacer, and I undercut the door jam with flush cut saw now. This will let the flooring slide, underneath the trim for a clean look and on the baseboards I’ll cover those gaps with quarter-round that I took off earlier.

I Cut the other side of the door too, and I cut into the baseboard a bit that I could slide the floor in cleanly under The whole jamb, so that wasn’t just a mistake. I did had on purpose Now. Next, I measured the transition channel for the door opening it has marks on the back where it’s supposed to snap cleanly, But it just bent when I tried to do it, so I grabbed a hacksaw and not cut to size instead.

I positioned the channel so that my finished transition piece would just hit the middle door stop. Then I secured it to the floor with screws and During my layout. I decided to take two and a half inches off the width of my initial starter row, And this will give me two and a half more inches of width on the other side of the Room to avoid those narrow strips That I mentioned earlier you’ll see that in just a bit Now my walls aren’t exactly straight either and I needed to account for that.

In this cut, I used the vinyl sheet design as a straight reference to lay the planks on, and I measured the gaps across the wall. If you’ve taken up the flooring or don’t have a reference line, You can always snap a chalk line and use that to reference.

The measurements. I Mark the first plank on both ends for this angled cut line. Vinyl plank flooring can be scored and cut with the utility knife, So I went ahead and grabbed my t-square to score the plank between my two marks.

The problem I found is when trying to snap the plank along that line, since I couldn’t really grab it and pull it up to snap it. I put a piece of scrap wood underneath the score line and Just beat on it with my mallet until it snapped.

As you can imagine., This went pretty badly. I quickly realized that scoring and snapping for the long cuts is not a great option. So instead I took it down to my shop and I laid out a new line That was a quarter inch in from that jagged mess that I just made.

Then I used a circular saw to cut the line and it turned out great now really. I was just trying to avoid using power tools as much as possible, But using a jig saw table saw or circular saw, is really the only way to go here.

The final plank is a floating floor and it needs to be held off the walls, a quarter-inch in all the directions. So to do this, I use these wedge spacers from the flooring install kit that I link and I taped them to the wall.

I laid down the first plank under the door jamb, but it was still a bit far from the metal channel. So I marked the piece along the door jamb and I used a jigsaw to quickly trim off that corner and then it fit in there.

Nice and smooth and The next piece gets dropped in and locked into that first piece and using a tapping block across the front on the seam Aligns the boards flush with each other, and this got me to my first partial board.

I measured the gap to the wall and I transferred it over to the board. Then I used a 12 inch carpenter square to score line on the plank with my utility knife.. I flipped it over and I snapped the plank by pulling up on the hand while supporting it behind that scoring line To finish the cut.

. I flipped it over and cut through the backing to release the piece. When I snapped this board, It really turned out a little bit jagged. It was because, when I scored the plank the second time, the blade veered off that original line a little bit So make sure if you’re gonna go over it twice that you stay on, that original line or you’re gonna need to clean up the edge.

Like I’m doing here, Hey If you like what you’re seeing so far and you haven’t done it already Go ahead and hit that subscribe button and ring that bell for some more great content.. I cut this small piece, the same width as the other first row boards, And then I installed it on the end now to pull the board tight, I used this small pull bar that hooks over the end of the board and helps you pull that into place.

Using a mallet now to start the second row, I cut a full plank down to 18 inches long, and This time was a lot more careful scoring that line and the piece snapped nice and clean Connecting the boards from here on out is pretty easy.

You just angle the tongue on the long edge into the groove of the road before it, and then you lower the plank and tap it into place. Using this tapping block from that kit that I mentioned earlier, a Few taps with a non marring mallet across that short seam also is gonna lock it into place Now working in a small room has a lot more stops and starts, because I could only put Down One or two full boards in each row before needing to make another cut At the end of this row, I had a really small cut to make off the end to make my board fit, And you can’t really score it and snap it because it’s just Too short, So go ahead and use a circular saw for this as well After I got the first two rows in.

I use some dumbbells to weight them down and keep that floating floor from moving as much There’s only so many different patterns on these planks. So I made different piles of them in the room to help keep the floor as random, as I could So when I came in to grab a board I’d rotate through them, so that the similar planks weren’t close to each other.

This is a great way to make sure that your floor looks as best as it can And while I’m working my way down these next few rows., Let’s talk about today’s sponsor Filter, buys a family-owned business, making hvac filters here in the US, and they have a Great origin story: Their Factory in Talladega Alabama has been in the family for three generations And they actually used to make parts for US tanks in World War.

Two in 2008, The factory almost shut down, But one of the grandsons of the original owner felt compelled to come by the facility from his grandfather and save the local jobs They switched over to making furnace filters.

And now they have over 600 sizes in stock, with free, 24-hour shipping and custom sizes available. I have a link down below in the description where you can find out more and thanks filter by for sponsoring this video.

When I got to the other door jamb, I had to notch the piece like before I Laid out the plank and I transferred marks where the door jamb was and how much I needed to take off. And when you’re doing this, I always try to err on the side of taking off too little versus too much so that you don’t get stuck with any big Gaps.

But after a few back-and-forth, I had it fitting really nicely to install the plank. I slid it up close to the door jamb and then locked it in place with that prior row. Then I used the tapping block on the end of the board and just tapped it in place until it slid all the way into The trim as you’re working through the room.

You can start using some of the offcuts from one in the room to start or finish the other end of the room. Keep that in mind to make the best use of your flooring. So you don’t have a bunch of scraps that you have unused at the end, It’s a little hard to see here, but I’m really staggering.

The seams of these planks. Randomly You want to avoid having a consistent spacing between seems like a brick laid pattern, because it just won’t look natural to the eye, And when I got to the bump-out on the other side of the room, I measured and marked the planks for the knotch.

And this corner was way out of square, So I made sure to measure at the beginning and the end of each side of that notch I made the angled cuts with my jig saw and taking that extra time Gave me a great fit When I got back To the sink vainly, you can see why I made that first road narrower than the full-width, because if I had have started with a full width plank, Then this little sliver in front of the vanity would have been under two inches.

I Also planned the staggers that I didn’t need to notch this narrow piece either, And I would just have a small notch on the next full-size plank Planning. These little details ahead of time is really gonna make your flooring install, go much smoother and look a lot nicer now, if you have a board that doesn’t want to lock into place, make sure to check the tongues and the grooves for debris a Little bit Of flooring got stuck in this groove and it kept it from seating properly Now.

Another little surprise in the install was this overflow drain in the floor. I’M gonna work around this, but if you have a floor outlet or another obstacle to work around, you can use these same steps.

I Measured the distance off the side of the cabinet and off of the back wall and Mark the plank. Then I used a Forstner bit a little bit larger than that pipe in the floor. The final flooring is pretty easy to drill through with normal woodworking bits.

So it goes pretty quickly And next I laid the board in place and I finished the row before putting an extension onto that drain. I just marked it and cut a one and a half inch to one of the quarter, inch PVC down pipe to length, and I installed It just below the surface.

I added a little bit of caulk around the edges and that gave me a nice watertight seal and it looks way nicer than that one Did before it and the water will have a place to go if it ever leaks. Out Now from here, I could reinstall my quarter round molding in my carpet transition, since this is a floating floor, Just make sure to nail into the baseboards and not into the floor when you’re putting on that molding and I cut the final transition piece to size And I see the lit in that metal.

You channel that I installed earlier with my mallet. This floor really brings the laundry room together.. It looks awesome in here. I think installing vinyl plank flooring is a great option for an easy install with a big impact and you’ll have some really durable flooring.

Hey if you want to see how I did that wainscotting in that room or how to tile a bathroom. I’Ve got a playlist for you right there with home renovation projects. I’Ve got another one for you down there as well that you might like until next time, guys.

Get out there and build something awesome.

Source : Youtube

Putting up my wood accent wall | Home Made Happy

Hey guys, how are you it is currently Wednesday for you, and actually it’s also Wednesday for me and um. I thought this week. I would make a little bit of progress on my living room because there’s just a couple things that need to get done to the accent wall for it to really, I think, fully come together.

Actually, let me show you also, I’m just enjoying my cup of red rose tea. My favorite type of tea so delicious, it’s an orange pico and I don’t like any other brand red rose all the way. So i know i need to do something here.

I was initially thinking of putting art on either side of the door, but now i’m thinking, maybe i should add, curtains and really just frame in the view that you have right when you look out which is trees, i mean you can’t see see if i focus Focus you kind of see that there’s like a tree view there, which is really nice, now focus back on me, hello.

I need to figure out something for that wall and then the other thing i need to do, obviously – which i think is what i’m gonna do this week over here this wall. Behind the two chairs i plan to do a wood panel wall, which i think is gonna look really really nice.

I did go ahead and pick up wood in the last video, as you saw, and so now i think it’s just about staining it waiting for it to dry and putting it up. Let’s go okay, so here is the plan for my wood flat wall.

I have all the pieces of wood right here behind me laid out. I think i actually bought a few too many, because i was initially anticipating the spacing between the pieces of wood to be smaller, but i think it should be a little bit more, but that’s.

Okay, it’s always better to have a little bit more than a little bit too little. So i’m going to go ahead and stain the pieces of wood. I picked up Varathane Early American, which is a color that i like quite a lot, and the goal here is to achieve a wood color that kind of matches the color of the faux wood beams that i have in the bedroom.

I mentioned this before, but one of the things i’m trying to do in this apartment is kind of carry some of the tones throughout the apartment to create a more cohesive space. Overall i felt like in my last apartment i had just started to do that, and it’s kind of one of the ways that you can make your space feel like it all goes together like each room.

They can be individually different, but then they have certain things, that kind of repeat certain tones. That repeat – and i think it just has a really nice effect. So that’s the goal here and i’m out of breath for some reason.

It’S really warm in this room. So i might open the window, so this is going to take longer than i anticipated. Oh before. What can you do? Okay, so, okay, very tight on my face. I need to take a break because my shoulder is killing me.

I’M unexpected for that to happen, but for me very expected, because it’s like a lot of repeated movements, but i’m just going to take a break and then hopefully, when i can come back, my husband can help me a little bit to make it go a little Bit faster because i just did 10 by myself and it just took a little bit.

It just takes a little bit longer than i expected. I think i have a helper okay, so we are actually running extremely low on stain, like literally. Nothing is dripping out of here and we’re just trying to make do to finish.

The last piece of wood like fingers crossed we’ll just scrape five but yeah. This is why i usually like to have an extra can of stain, just because i find it so hard to really tell how much i need and then, if you go over, you can always return the extra can, but in this case really running low.

So we’ll see, there’s literally nothing left in here and good news for us. We did manage to finish all of the staining, with the limited amount of stain that we had left so hallelujah. I am so pleased about this time to get out of this room and let all of the stain dry together ooh, it’s so pretty out here so lovely good morning.

It is now several days later. Actually, i should say good afternoon: it’s 1 48., but it has been several days and i’ve just kind of left the wood pieces in that room night after night to air out into off gas from the stain.

That’s essentially what i’m doing when i’m trying to leave it like for quite a long time without being in my actual living space, because the off-gassing is toxic. Essentially so if you can smell it, it’s probably not done, and that means that vocs are going into the air and that’s toxic for your health.

So i’ve kind of left that there for as long as i can the window has been open and it’s been airing out day after day. I don’t think i can wait any longer. So let’s go ahead and let’s check to see how bad the smell is.

Fingers crossed it’s either gone or not that bad must close the windows. It is extremely cold in here i am like shivering. It is so cold, but that’s okay, right now. What i’m gonna do is. I guess i also.

Let me just show you what the coloring is looking like a little bit variable, that’s probably because i didn’t use like a wood, conditioner and also it’s pine and pine tends to do this, so i guess i’m going to just start taking these out to the living Room because it’s cold in here, so i don’t want to continue working in here, so i’m just going to take them out and then we’ll move to the next steps.

So strong, let’s go! Oh also. I didn’t stain the bottom side in case you’re, just noticing that now only the sides and the top, not the bottom. So i now have all of the boards behind me and i pulled out my little stash of command strips, which is like a jumbo pack that i got from costco this time, except i’ve had this for months, just like just in case.

I ever need to hang something impromptu. You know i just did some simple mathematics and realized. I do not have enough command strips, but i don’t think i’m gonna. Let that stop me and also my mom is not home and i can’t go to the store to get any additional command strips, so we’re just going to proceed and put on what i can for right now and then see how far it goes.

You know – maybe maybe i should ask my mom – hangs up to 15 frames. This is a time-consuming process when you have to do it like 40 times. You know one two, three, four, five, eleven twelve, thirteen, eight twenty nine thirty.

I have thirty. That means i can do fifteen right now. Oh also, i just to update you. I brought the boards out here and i can’t smell the stain pretty much at all, so we’re good okay, so i think i’ll just do what i can right now and then i’ll get more tonight.

I don’t know, oh also. Let’S all please observe this dying. Greenery pot that i need to change and i actually have the greenery to change it, but i’ve gotten so lazy and now they’re turning yellow because they’re also in the sun, so just wanted to highlight it and now we’ll ignore it.

3M command. Ships can sponsor me at any time. You know if they want to send me free command, strips that’d, be nice too spent a small fortune on them, don’t regret and now to make them all stick down because you’re supposed to press these down for like a minute.

So ouch, so now what i’m gonna do is beauty. So one thing i didn’t actually mention about this wall is that it has a phone jack here i actually have a landline and i love it. So don’t come for me. Okay, there’s no way to avoid it all together, so i’m hoping that the piece of wood will somehow be able to sit on top of this, which i’m now looking at it.

I don’t know that it will be able to, but that was my hope and then that i wouldn’t have to cut it, but if it does overlap then i will have to cut it so far. This has still worked. Pretty well feels super secure.

So one panel up and ready to go so good morning. It is now the next day and all clearly, as far as i got was putting up one beam and then i got stuck and my husband and i just spent the last, like 30 minutes, trying to figure out different items that we could use to space the Gaps between the pieces of wood and i think we landed on using his phone.

I also picked up some extra command strips i’m gonna put these on and then we’re gonna put them on should be good. Also, it’s a beautiful sunny day. Oh so i can’t complain. Okay, are we ready so we’re gonna use your phone as a spacer yeah? Oh my god, i’m so uncoordinated.

Today, okay, oh no! The bottom has sucked the bottom. That was stressful, cool all right next next one. So, oh my god, my you, no we’ll have to stain this one later, because i guess this end was stained, but this end wasn’t what monkey the full view is even funnier all right, my next! I have no clue you guys.

I don’t know what to say. Other than i love it literally, i love it so much. I think that it just matches so well with the vibes of the wood beams in my bedroom, and i just feel like it ties the place together so much more.

Obviously, i still have some remodel work to do, because i need something i think to go in the center of the wall. I also need some new cushions here. I might build a bench or some sort of console right behind the chairs, but i absolutely love it.

I think it’s stunning, this is where i sit and do my work usually – and i have my little stool next to me – and i do this before i do this fun fact. Oh, and in case you were wondering you cannot see the command strips from the side.

I was worried, you’d be able to see them, can’t see them on any of them, including the last one which has the edge facing well facing us. Okay, bye,

Source : Youtube